SN74HCS86QDRQ1 IC 4 Channel Schmitt Trigger Input 14-SOIC 74HCS86 XOR (Exclusive OR) IC 4 Channel Schmitt Trigger Input 14-SOIC Specification : Logic Type XOR (Exclusive OR) Number of Circuits 4 Number of Inputs 2 Features Schmitt Trigger Input Voltage - Supply 2V ~ 6V Current - Quiescent (Max) 2 µA Current - Output High, Low 7.8mA, 7.8mA Logic Level - Low 1V ~ 3V Logic

RF Power LDMOS Transistors High Ruggedness N--Channel Enhancement--Mode Lateral MOSFETsThese high ruggedness devices are designed for use in high VSWR industrial (including laser and plasma exciters), broadcast (analog and digital), aerospace and radio/land mobile applications. They are unmatched input and output designs allowing wide frequency range utilization, between 1.8 and 600 MHz.  Typical Performance: VDD = 50 Volts, IDQ = 100 mA Category Discrete Semiconductor Products 　 Transistors - FETs, MOSFETs - RF Mfr NXP USA Inc. Transistor Type

The ATtiny261A/ATtiny461A/ATtiny861A of microchip provides the following features: 2/4/8K byte of In-System Programmable Flash, 128/256/512 bytes EEPROM, 128/256/512 bytes SRAM, 16 general purpose I/O lines, 32 general purpose working registers, an 8-bit Timer/Counter with compare modes, an 8- bit high speed Timer/Counter, a Universal Serial Interface, Internal and External Interrupts, an 11-channel, 10-bit ADC, a programmable Watchdog Timer with internal oscillator, and four software selectable power saving modes. Idle mode stops the CPU while allowing the SRAM, Timer/Counter, ADC,

LCD1602 2 line 16 characters LCD Display LCM display module 3.3V 5.0VThis is a high quality 16 character by 2 line intelligent display module, with back lighting, Works with almost any microcontroller.Features:16 Characters x 2 LinesModel : 1602ASpecies :The LCD screenThe screen size : 2.4 (inches)color :Blue screenBrightness :The highlightedContrast : AdjustablePixel :16 * 2Distance : 0.55 * 0.60 (mm)The response time : 0.01 (ms)Viewing Angle :(180 °)Specification:

interface expansion board Edge Breakout for micro bit  adapter board IO expansion boardIntroduction:I am an interface expansion board specially designed for micro:bit, which expands the 2.54mm pitch pin header interface for  micro:bit to facilitate various experiments.Parameters :Dimensions: 82.05mm × 36.10mmThrough hole diameter: 2mmFamily                                                         Interface  Board    

Name : 2.4G 5G 5.8G multifrequency PCB 5dB Antenna Wifi module with IPEX interface 146153-Series   1461530250Description:Standing wave ratio definition: S.W.R <= 2.0 @ 2400 MHz ~ 2700 MHz                                                    S.W.R <= 2.0 @4900 MHz ~5900 MHzGain definition: 5dBi ( *Typical* )Band definition: 2400 MHz ~ 2700 MHz@4900 MHz ~5900 MHzImpedance definition: 50 ohmOperation Temperature - 40 °C ~ + 65 °CStorage Temperature - 40 °

RB-02S046  2.2 Bending  flex Sensor Robotic Electronic Gloves Recommended for  Arduino The Flex Sensor By Spectra Symbol is a simple sensor for measuring bending strength. With an ultra-thin package, it can be attached to the surface to be measured, and the analog output is convenient for collecting and processing the bending information. The total length of 80mm is as long as 60mm, and the controller with AD conversion is especially suitable for finger bending detection, robots, medical equipment, musical instruments and other products.Specifications:1. Product Name:

Mini USB Host Shield 2.0 ADK SLR Module Development ToolDescription: 1. Support Google for Android ADK, support Android phones: G1, Nexus One, Nexus S, Droid X.     (Mobile systems need to be upgraded to Android 2.3.4, tablets need to be upgraded to Android 3.1)2. Provide the APK package and compile the source file ADK3. Compatible with the following hardware of arduino:      For arduino Uno 328      For arduino Diecimila / Duemilanove 328      Suitable for arduino Mega 2560 (recommended)      For arduino Mega 1280

SPF5189 RF Low Noise Amplifier LNA 50-4000MHz Specification ：LNA：50-4000mhzNF：SPF5189ZLNA0：0.6 dBAmplifier：FMSize ：34 x 25mm / 1.33 x1.0inchWeight ：10gFeature:This RF amplifier has a low noise figure and is an LNA RF amplifier.A high frequency or intermediate frequency preamplifier that is commonly used as a variety of radio receivers, as well as an amplifying circuit for high sensitivity electronic detection equipment.In the case of amplifying a weak signal, the noise of the amplifier itself may be very severe, so it is desirable to reduce this noise to improve the signal-to-noise

GY-471 MAX471 3A Range Current Sense Module Sensor Current MeasurementDescription:This module can be used to test the current and voltage.The principle of voltage test based on principle of resistive voltage divider design, can make the red terminal connector input voltage to 5 times smaller. analog input voltages up to 5 v, the voltage detection module input voltage not greater than 5Vx5=25V (if using 3.3V systems, input voltage not greater than 3.3Vx5=16.5V). AVR chips have 10-bit AD, so this module simulates a resolution of 0.00489V (5V/1023), so the minimum voltage of input voltage

GY-213V-HDC1080 High Accuracy Digital Humidity Sensor module with Temperature Sensor,HDC1080 module Low Power 

Programming serial interface module chip AD9833 sine wave signal generator DDS module GY-9833AD9833 sine wave signal generator DDS module GY-9833General description:The AD9833 is a low power, programmable capable of producing sinusoidal waveform generator, triangular, and square wave outputs. Generation is required in various types of waveform detection, implementation, and time domain reflectometry (TDR) applications. the output frequency and phase are programmable software, allowing easy tuning. without external components are needed. The frequency registers are 28 bits wide: with a 25MHz

VL6180X Time-of-Flight Distance Sensor Carrier with Voltage Regulator GY6180 for ArduinoGY-6180 VL6180X  Light sensor, ranging, gesture recognitionFeatures:2.8V Regulator - Provides the required 2.8V for the sensorI2C Level Shifter - Provides logic level conversion from 2.8V to VCC3-in-1 ModuleIR EmitterRange SensorAmbient Light SensorMeasures absolute range up to 10cmGesture RecognitionI2C InterfaceTwo Programmable GPIOSharp Sensor Board LayoutDescription:VIN This is the main 2.7 V to 5.5 V power supply connection. The SCL and SDA level shifters pull the I²C lines high to this level.GND

Heart Rate Click Sensor GY-MAX30100 Heart Rate Oxygen Concentration Sensor Module MAX30100Heart Rate Click Sensor GY-MAX30100Main integrated circuits : MAX30100Voltage  : 3-5VSize ：14mm*14mmCommunication protocol :I2CDescription:Heart Rate click carries Maxim’s MAX30100 integrated pulse oximetry and heart-rate sensor. It’s an optical sensor that derives its readingsfrom emitting two wavelengths of light from two LEDs – a red and an infrared one – then measuring the absorbance of pulsing blood through aphotodetector. This particular LED color combination is optimized for reading the data

6 axis attitude acceleration gyroscope GY-6500 MPU6500 6DOF Sensor Modules  GY-6500 MPU6500 6DOF Sensor ModulesMain Features:● This module contains 16-bit ADC output of 3 axis accelerator and 3 axis gyro● Model: GY-6500● Chip: MPU6500● Power voltage: 3 - 5V● Communication mode: I2C / SPI● Gyro range: + / -250, + / -500, + / -1000, + / -2000dps● Accelerator range: + / -2G, + / -4G, + / -8G, + / -16G● Register: 1MHz● SPI / I2C: 400KHz● Gyro working current: 3.2mA● Gyro sleeping current: 8uA● Accelerator working current: 450uA● Accelerator sleeping current: 8uA●

{{item.prod_desc}}